NRS

Frame U-Style Raft Motor Mount

$249.95 USD
MSRP
NRS - Frame U-Style Raft Motor Mount

Product Information

When you want to run your motor while sitting on the stern seat, you need the NRS U-Style Raft Motor Mount. It places the motor far enough from the raft's stern for easy operation of the control handle.

  • This mount is also a good choice when you have a heavy motor; the curved bars resting against the raft's tubes support the weight.
  • We use our heavy-duty 1-5/8" OD 6061-T6 aluminum pipe to make the framework for the Motor Mount.
  • The 1 1/2" x 7 1/2" x 18" wide transom plate is a piece of wood/plastic composite decking material that will not rot or deteriorate when exposed to water and sun.
  • We back the transom plate with two pieces of aluminum channel to increase the grip on the upright pipe sections. Four 4 1/4" motor mount U-bolts hold the transom plate firmly in place.
  • If you already have an NRS Stern Seat Mount, you can install your Motor Mount on either side of the seat plate.
  • If you're not using a stern seat, the Motor Mount comes with a 24" piece of frame pipe for attaching the Mount to the Stern Rails.
  • If you do not have a Stern Seat Mount you will need a pair of NRS Stern Side Rails (item #90022.02, sold separately) to link the Motor Mount to the rear Cross Bar of your frame. We stock three sizes: the two Small Stern Side Rails, in 32" and 39" lengths, work best for 54" and narrower frames. The 36" Large Rails work best for 60"or wider frames. Measure the distance from the center of the rear cross bar to the center of the raft's rear tube. If you need a length other than our stock sizes, we will custom bend the size you need.
  • The bars, where they attach to the transom plate, are 14" apart, center-to-center. If you have valves on the outside of the stern panel, and that spacing interferes with their operation, we can make you a custom transom plate.
  • The distance from the center of the attachment bar to the center of the upright bars is 25".
  • The transom plate can be mounted on either side of the uprights, and adjusted up and down as needed.
  • The Mount fits raft tubes 18"-24" in diameter.
  • In our experience, a 10-hp motor is generally as large a motor as most boaters use. Even a 3-hp motor will move a raft along at a pretty good clip.
  • Always attach a safety rope or strap from your motor to the frame.

Not in stock. Contact a dealer for info.
Change

Select a Store

Selected Store

19 locations
18 other locations

REI - Fairfax

11950 Grand Commons Ave
Fairfax, VA 22030
Other NRS Available
14.9 mi
Open Info

REI - Tysons

8209 Watson St
McLean, VA 22102
Other NRS Available
16.4 mi
Open Info

REI - Rockville

910 Rose Avenue
North Bethesda, MD 20852
Other NRS Available
20.0 mi
Open Info

REI - Bailey's Crossroads

3509 Carlin Springs Rd
Bailey's Crossroads, VA 22041
Other NRS Available
23.9 mi
Open Info

REI - Washington DC Flagship

201 M St NE
Washington, DC 20002
Other NRS Available
27.2 mi
Open Info

REI - Woodbridge

15200 Potomac Town Pl #140
Woodbridge, VA 22191
Other NRS Available
31.0 mi
Open Info

REI - Columbia

6100 Dobbin Rd
Columbia, MD 21045
Other NRS Available
37.4 mi
Open Info

River Rock Outfitter

[full star] [full star] [full star] [full star] [full star] (10)
215 William Street
Fredericksburg, VA 22401
Other NRS Available
51.4 mi
Open Info

REI - Timonium

63 W Aylesbury Rd
Timonium, MD 21093
Other NRS Available
53.3 mi
Open Info

L.L. Bean

8095 Tysons Corner Center
McLean, VA 22102
Authorized NRS Dealer
17.0 mi
Info

L.L.Bean

925 Rose Avenue
North Bethesda, MD 20852
Authorized NRS Dealer
20.0 mi
Info

Mid-Atlantic Rescue Systems

11 Byte Ct Ste A
Frederick, MD 21702
Authorized NRS Dealer
28.8 mi
Info

Safeware Inc.

4403 Forbes Blvd
Lanham, MD 20706
Authorized NRS Dealer
36.0 mi
Info

Wetsuit Wearhouse

400 S Conococheague Street
Williamsport, MD 21795
Authorized NRS Dealer
41.7 mi
Info

Virginia Outdoor Center

3219 Fall Hill Ave
Fredericksburg, VA 22401
Authorized NRS Dealer
50.4 mi
Info

Annapolis Canoe and Kayak

311 Third St ste b
Annapolis, MD 21403
Authorized NRS Dealer
54.4 mi
Info

Sportsman's Warehouse

3285 Black Gap Rd
Chambersburg, PA 17202
Authorized NRS Dealer
63.3 mi
Info

Cumberland Marine Repair LLC

40 Aberdeen Rd
York, PA 17406
Authorized NRS Dealer
78.1 mi
Info

TCO Fly Shop - Boiling Springs

[full star] [full star] [full star] [full star] [full star] (1)
2 E 1st St
Boiling Springs, PA 17007
Authorized NRS Dealer
78.6 mi
Open Info

Product Information

When you want to run your motor while sitting on the stern seat, you need the NRS U-Style Raft Motor Mount. It places the motor far enough from the raft's stern for easy operation of the control handle.

  • This mount is also a good choice when you have a heavy motor; the curved bars resting against the raft's tubes support the weight.
  • We use our heavy-duty 1-5/8" OD 6061-T6 aluminum pipe to make the framework for the Motor Mount.
  • The 1 1/2" x 7 1/2" x 18" wide transom plate is a piece of wood/plastic composite decking material that will not rot or deteriorate when exposed to water and sun.
  • We back the transom plate with two pieces of aluminum channel to increase the grip on the upright pipe sections. Four 4 1/4" motor mount U-bolts hold the transom plate firmly in place.
  • If you already have an NRS Stern Seat Mount, you can install your Motor Mount on either side of the seat plate.
  • If you're not using a stern seat, the Motor Mount comes with a 24" piece of frame pipe for attaching the Mount to the Stern Rails.
  • If you do not have a Stern Seat Mount you will need a pair of NRS Stern Side Rails (item #90022.02, sold separately) to link the Motor Mount to the rear Cross Bar of your frame. We stock three sizes: the two Small Stern Side Rails, in 32" and 39" lengths, work best for 54" and narrower frames. The 36" Large Rails work best for 60"or wider frames. Measure the distance from the center of the rear cross bar to the center of the raft's rear tube. If you need a length other than our stock sizes, we will custom bend the size you need.
  • The bars, where they attach to the transom plate, are 14" apart, center-to-center. If you have valves on the outside of the stern panel, and that spacing interferes with their operation, we can make you a custom transom plate.
  • The distance from the center of the attachment bar to the center of the upright bars is 25".
  • The transom plate can be mounted on either side of the uprights, and adjusted up and down as needed.
  • The Mount fits raft tubes 18"-24" in diameter.
  • In our experience, a 10-hp motor is generally as large a motor as most boaters use. Even a 3-hp motor will move a raft along at a pretty good clip.
  • Always attach a safety rope or strap from your motor to the frame.

Product Reviews

There are no reviews yet for NRS: Frame U-Style Raft Motor Mount .

Write a Review